Closed Ampoule Filler and Sealer

Closed Ampoule Filler and Sealer

Closed Ampoule Filler and Sealer Model LI-AFS C is uses for filling and sealing process of type D pre-sterilized closed ampoules. Machine model built on principle of slant travel of ampoules while filling and sealing, to take care of vide variation of ampoule neck dimensions, thicknesses of available standard ampoules.


The Closed Ampoule Filler and Sealer unit built on stainless steel square pipe frame and totally encompassed with stainless steel coverings, in pleasing matt finish. Further, large opening section is specially designed at front end bottom side of the machine for easy cleaning. The pendant type electrical control panel is lifted from machine for ease of operation and safety. Machine is suitable for Ampoule Filling in pharmaceutical, cosmetic, agriculture and chemical industries.


Salient Features:

  • Compact GMP model.
  • Suitable for filling and sealing of type ‘D’ ampoules.
  • All contact parts made from AISI SS 316L & other Non-contact parts made from AISI SS 304.
  • Minimum change over parts from 1ml to 10ml ampoule size.
  • "No Ampoule - No Filling" system.
  • Ampoule neck centering during gas flushing and filling operations.
  • Possibility of nitrogen gas flushing before, during and after filling.
  • Full accessibility allows easy maintenance.
  • Machine equipped with pre-warming station.
  • Minimum change over time, little maintenance & easy cleaning.

Process Operation:

Pre-Sterilized D Type Ampoule tray can be directly loaded into slant hopper of the machine. The magazine type cassette delivers closed ampoules on moving eccentric ampoule rack in one/two/four/six/eight’s. Ampoule rotating lever rotate the ampoules and extreme pressure of the gas heat the ampoules. Ampoule opening process is done by the manner of pre-heating and opening with the pressure of the gas (LPG + oxygen). During the stoppage of rack sequentially ampoule opening, pre-gassing, filling, post gassing, pre-heating and final sealing is achieved. Filled & sealed ampoules are collected automatically in SS tray in upright position without hand touch.


Technical Specification:

Sr.No.Machine ModelLI-AFS 1CLI-AFS 2CLI-AFS 4C
1.No. of HeadSingleTwo Four
2.Direction of MovementLeft to RightLeft to RightLeft to Right
3.Ampoule Handling Range1 ml to 10 ml1 ml to 20 ml1 ml to 5 ml
4.Production Output15 to 30
ampoules/minute
30 to 55
ampoules/minute
55 to 100
ampoules/minute
5.Filling Accuracy± 1%± 1%± 1%
6.Require Gas for SealingLPG & Oxygen (O₂)LPG & Oxygen (O₂)LPG & Oxygen (O₂)
7.Nitrogen Pressure Required1 Kg. /cm21 Kg. /cm21 Kg. /cm2
8.Oxygen Pressure Required1 Kg. /cm21 Kg. /cm21 Kg. /cm2
9.LPG Pressure Required0.5 Kg. /cm20.5 Kg. /cm20.5 Kg. /cm2
10.Power Specification0.5 H.P1 H.P.1 H.P.
11..Electrical Characteristics230 Volts, Single Phase, 50 Hertz, 4 Wire System230 Volts, Single Phase, 50 Hertz, 4 Wire System230 Volts, Single Phase, 50 Hertz, 4 Wire System
12..Contact PartsMade from Stainless Steel 316LMade from Stainless Steel 316LMade from Stainless Steel 316L
13.Non-Contact PartsMade from Stainless Steel 304Made from Stainless Steel 304Made from Stainless Steel 304
14.Overall Dimension915mm (L) x 610mm (W) x 965mm (H)915mm (L) x 760mm (W) x 965mm (H)1200mm (L) x 1070mm (W) x 965mm (H)
Send Inquiry